Paver Stone Mold PS 30073

Paver Stone Mold PS 30073

Paver stepping stone molds PS 30073


Mold's (stone) thickness 1 inch ( 2.5 cm)

Approximate Mold measurement:  9 3/4" X 9 3/4" X 1" (25 cm X 25cm X 2.50 cm)


How to Make Concrete Stone Instruction


 

   PAVER STONE PLASTIC MOLDS  

Application areas for paving stones include residential terrace, schools, traffic and pedestrian walkways, road embankments, industrial and commercial buildings, landscape for open and closed court yards, churches and mosques.

 

1.    Plastic paver molds produce smooth and high quality paver stones and paver tiles.

2.    Different patterns of paver stone and tile molds are available for precast concrete process.

3.    Paver stones and tiles can be manufactured with a minimum infrastructure.

4.    Paver molds are in different shapes (square, rectangle and interlocking) and sizes.


  PS 30073 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.
PS 30073 mold casting weight is about 5.49 lbs. (2.49 kg.)
We use this 1:2 cement to filler ratio mix : (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)
1.83 lbs (0.83 kg) Portland cement (white for light stone colors, gray for dark stone colors)
3.66 lbs (1.66 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)
7.31 oz (0.2 L) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)
0.29 oz (8.3 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)
For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.
Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)
To color different molds sections, brush oxide pigment over the  selected sections, then cast the concrete.
Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours

Write a review

Note: HTML is not translated!
    Bad           Good

  • Product Code: PS 30073
  • Availability: In Stock
  • $23.00
  • 10 or more $18.00
  • 30 or more $15.00
Concrete admixture-Water reducer-Super plasticizer High-performance superplasticizer for cement bas..
$17.00

CSA Cement Fast Setting Additive 50 Lbs   GlobMarble CSA Cement is a cementitious po..
$27.50

Concrete Oxide PigmentOxide Concrete Colors for Concrete. 1Lb-(0.45kg) Mix Ready bag. Photos of..
$5.30

Non-Aerosol Sprayer for Release AgentThe Non-Aerosol sprayer is an economical alternative to aeros..
$64.99

Superplasticizer Melment F10 High-performance superplasticizer for cement and calcium sulphate based..
$9.50

White Concrete PigmentTitanium Dioxide White Colors for Concrete.   SELECT COLO..
$7.99

   PAVER STONE RUBBER MOLDS  There aredifferent mold models but it is the same M..
$32.00

Paver stone molds  PS 22106  There aredifferent mold models but it is the same Mold ..
$14.99

Paver stone molds PS 28044/1Approximate Mold measurement: 7 1/2" X  9 3/4" X  2 1/4" ..
$14.99

Chopped Basalt Fibers 1" ( 6-LB bag)   Chopped Basalt Fibers used to strengthen concrete pour ..
$41.00

Concrete Countertop Molds Edge Form CEF 7010Concrete Countertop Molds Edge Forms are used ..
$45.00

Water-Based Concrete Stains-Eco-Stain  Semi-transparent Concrete Stains from SureCrete (..
$60.00

Color Pack for Decorative Concrete - Xtreme PreCast Mix - 0.5 lb (0.23 kg) from SureCreteConcre..
$3.95

Concrete Countertop Mold Edge Form CEF 7012 Concrete Countertop Mold Edge Forms are ..
$40.00