Antique Brick Stone Mold BS 613, 23.5" x 17.25"

Antique Brick Stone Mold BS 613, 23.5" x 17.25"

Concrete Brick Stone Molds 

Antique Brick Stone Mold BS 613/1, BS 613/2, BS 613/3

Mold size — 3 sq.ft. (0.28 m2) approximate.

Measurements — 23 1/2” x 17 1/4” x 1” (60 cm x 44 cm x 2.5cm)

Mold sections — 14

Section dimensions: Approx. size of each section 7 1/2” x 2 3/4” x 1/2" (19 cm x 7 cm x 0.50 cm).

Antique Brick Stone Mold BS 613/4 Corner

Mold size — 1.93 sq.ft. (0.18 m2) approximate.

Measurements - 24” X 9” X 5” (61 cm X 23 cm X 12.50 cm)

Mold sections — 7

Section dimensions: Approx. size of each section from 3 1/2" x 2 3/4" x 1/4"

(9 cm x 7 cm x 0.50 cm) to 7 1/2” x 2 3/4” x 1/2" (19 cm x 7 cm x 0.50 cm)


How to cast GlobMarble brick stone mold instruction

How to Cast Corner Molds Instruction


Stone Veneer Mold


BS 613 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.

BS 613 mold casting weight is about 12.07 lbs (5.48 kg)

We use this 1:2 cement to filler ratio mix: (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)

4.03 lbs (1.82 kg) Portland cement (white for light stone colors, gray for dark stone colors)

8.04 lbs (3.65 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)

16.10 oz (0.43 l) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)

0.63 oz (18.28 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)

For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.

Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)

To color different molds sections, brush oxide pigment over the selected sections, then cast the concrete.

Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours

Frequently Asked Questions about Concrete Stamp Mats

Q: What is the difference between BS 613/1, 613/2 etc?

A: It the same family molds. Each mold has its own set of unrepeated to previous mold stone pattern. We’re recommend to cast several molds for wider variety stone pattern on surface.

Please leave a review

Review Button
  • Product Code: BS 613
  • Availability: In Stock
  • $113.40

Available Options

Concrete Vibrating MotorVibrating Motors for Concrete Vibrating Table     Concrete Vibrat..

CONCRETE MOLD RELEASE - G-1CONCENTRATED 30:1 FORMULAOur Concrete Mold Release soluble concrete relea..

Concrete admixture-Water reducer-Super plasticizer High-performance superplasticizer for cement bas..

CSA Cement Fast Setting Additive 50 Lbs   GlobMarble CSA Cement is a cementitious po..

Concrete Oxide PigmentOxide Concrete Colors for Concrete. 1Lb-(0.45kg) Mix Ready bag. Photos of..

Non-Aerosol Sprayer for Release AgentThe Non-Aerosol sprayer is an economical alternative to aeros..

Old Brick Stone Mold BS 611/1, BS 611/2, BS 611/3Mold size — 3 SQ.FT.(0.28m2) approximate.Measu..

Concrete Countertop Molds Edge Forms are used to change the shape of the edges of a concrete element..

Stepping Stone Molds. WS 5002Mold size 3.87 SQ.FT(0.36 m2) approximate.Measurements - 27 1/2" x 20 1..

Concrete Stepping Stone Mold Log WS 5901/1 Stepping stone mold diameter — 16 x 2" thick. ..

Color Pack for Decorative Concrete Overlay and Casting Products - 0.5 lb. (0.23 kg) Concrete co..

Water-Based Concrete Stains-Eco-StainSemi-transparent Concrete Stains from SureCreteSemi-Transparent..

White Concrete PigmentTitanium Dioxide White Colors for Concrete.   SELECT COLO..

Stamped Concrete Colored Powder Concrete Release Agent From SureCreteDescriptionConcrete Powder Rele..