Paver Stone Mold PS 12049/R, 8" x 4"

Paver Stone Mold PS 12049/R, 8" x 4"

Rubber molds for concrete stone


Paver stone molds PS 12049/1 & PS 12049/3

Mold (Stone) thickness 2.36 inch (6cm)

Approximate Mold inside measurement:  8 " X 4" X  2 1/4" (20cm X 10cm X 6cm) 


Paver stone molds PS 12049/2 & PS 12049/4

Mold (Stone) thickness 2.36 inch (6cm)

Approximate Mold outside measurement:  8 " X 4" X  2 1/4" (20cm X 10 cm X 6cm) 

Sections- 2.

Each Section Inside Dimension: 4" X 4" X 2 1/4" (10cm X 10cm X  6cm)



PS-12049 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.
PS-12049 mold casting weight is about 4.15 lbs. (1.89 kg.)
We use this 1:2 cement to filler ratio mix : (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)
1.38 lbs (0.63 kg) Portland cement (white for light stone colors, gray for dark stone colors)
2.77 lbs (1.26 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)
5.54 oz (0.15 L) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)
0.22 oz (6.29 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)
For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.
Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)
To color different molds sections, brush oxide pigment over the  selected sections, then cast the concrete.
Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours



These molds are designed to create own design decoration, to give your pavements and yard some artistic sense.

   

   PAVER STONE RUBBER MOLDS  

Application areas for paving stones include residential terrace, schools, traffic and pedestrian walkways, road embankments, industrial and commercial buildings, landscape for open and closed court yards, churches and mosques.

 

1.    Rubber paver molds produce smooth and high quality paver stones and paver tiles.

2.    Different patterns of paver stone and tile molds are available for precast concrete process.

3.    Paver stones and tiles can be manufactured with a minimum infrastructure.

4.    Paver molds are in different shapes (square, rectangle and interlocking) and sizes.

To have a wider stone pattern variety we recommend buying the following molds together:


PS 12049R/1 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.
PS 12049R/1 mold casting weight is about 4.15 lbs. (1.89 kg.)
We use this 1:2 cement to filler ratio mix : (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)
1.38 lbs (0.63 kg) Portland cement (white for light stone colors, gray for dark stone colors)
2.77 lbs (1.26 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)
5.54 oz (0.15 L) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)
0.22 oz (6.29 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)
For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.
Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)
To color different molds sections, brush oxide pigment over the  selected sections, then cast the concrete.
Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours



PS 12049R/2 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.
PS 12049R/2 mold casting weight is about 2.08 lbs. (0.94 kg.)
We use this 1:2 cement to filler ratio mix : (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)
0.69 lbs (0.31 kg) Portland cement (white for light stone colors, gray for dark stone colors)
1.38 lbs (0.63 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)
2.77 oz (0.08 L) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)
0.11 oz (3.14 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)
For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.
Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)
To color different molds sections, brush oxide pigment over the  selected sections, then cast the concrete.
Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours

Please leave a review

Review Button
  • Product Code: PS 12049R
  • Availability: In Stock
  • $28.66
  • 10 or more $19.00
  • 30 or more $15.00

Available Options

CONCRETE MOLD RELEASE - G-1CONCENTRATED 30:1 FORMULAOur Concrete Mold Release soluble concrete relea..
$23.00

Premium Acrylic Concrete Sealer HS-200 From SureCreteClear Stamped Concrete Driveway And Pool Deck S..
$61.40

Concrete admixture-Water reducer-Super plasticizer High-performance superplasticizer for cement bas..
$21.78

CSA Cement Fast Setting Additive 50 Lbs   GlobMarble CSA Cement is a cementitious po..
$38.80

Concrete Oxide PigmentOxide Concrete Colors for Concrete. 1Lb-(0.45kg) Mix Ready bag. Photos of..
$5.91

Non-Aerosol Sprayer for Release AgentThe Non-Aerosol sprayer is an economical alternative to aeros..
$68.30

Paver stone rubber mold   PS 21104   Mold's (stone) thickness 2.36 inch ( 6 cm) Approxima..
$28.66

Paver stone molds PS 24107R (rubber) Mold's (stone) thickness 2.36 inch ( 6 cm) Approximate mold me..
$33.65

Color Pack for Decorative Concrete Overlay and Casting Products - 0.5 lb. (0.23 kg) Concrete co..
$5.70

Rubber molds for concrete stone     PAVER STONE MOLDS   Application ar..
$38.63

Paver stepping stone molds PS 5017Plastic molds for concrete stone with texture ( similar to 40 grit..
$39.69

Concrete Countertop Molds Edge Forms are used to change the shape of the edges of a concrete element..
$56.70

Water-Based Concrete Stains-Eco-StainSemi-transparent Concrete Stains from SureCreteSemi-Transparent..
$85.10

White Concrete PigmentTitanium Dioxide White Colors for Concrete.   SELECT COLO..
$10.29

Stamped Concrete Colored Powder Concrete Release Agent From SureCreteDescriptionConcrete Powder Rele..
$95.29