Paver Stone Mold PS 8048

Paver Stone Mold PS 8048

Paver stone molds PS 8048

PS 8048/1R

Rubber mold for concrete paving stone

Molds (stone) thickness 2 1/2" (6 cm)

Approximate Mold measurement:  8 1/4" X 8 1/4" X  2 1/2" (21cm X 21cm X 6cm)  

PS 8048/2, Plastic

Molds (stone) thickness 2 1/2" (6 cm)

Sections -1

Approximate Mold measurement:  8 1/4" X 8 1/4" X  2 1/2" (21cm X 21cm X 6cm)  

PS-8048 Stone-casting Instructions:

Always apply release agent to your mold prior to casting concrete.
PS-8048 mold casting weight is about 9.82 lbs. (4.46 kg.)
We use this 1:2 cement to filler ratio mix : (you can also mix 1-part Portland cement to 3 parts sand [filler], but plasticizer and water has to be re-calculated by cement weight)
3.27 lbs (1.49 kg) Portland cement (white for light stone colors, gray for dark stone colors)
6.55 lbs (2.97 kg) Sand (20-30 mesh recommended. Silica sand or "all-purpose" sand works great)
13.09 oz (0.36 L) Water (We recommend water to be 20%-30% of cement weight.) (If your mix is too liquid, use less water.)
0.52 oz (14.86 g) Super-plasticizer (Superplasticizer's dosage rate is 0.5% -1% of cement weight. We are using 1%)
For best result always add dry pigments to your mix prior to adding the water. Mix concrete with pigment and additives for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting, then mix with dry ingredients.
Please note: Concrete minimum mixing time is 3 minutes (it takes a few minutes until Super Plasticizer absorbs into the cement and start reaction)
To color different molds sections, brush oxide pigment over the  selected sections, then cast the concrete.
Cover the mold with plastic while it is curing. Remove the stone from the mold in 12-24 hours



Application areas for paving stones include residential terrace, schools, traffic and pedestrian walkways, road embankments, industrial and commercial buildings, landscape for open and closed court yards, churches and mosques.


1.    Plastic paver molds produce smooth and high quality paver stones and paver tiles.

2.    Different patterns of paver stone and tile molds are available for precast concrete process.

3.    Paver stones and tiles can be manufactured with a minimum infrastructure.

4.    Paver molds are in different shapes (square, rectangle and interlocking) and sizes.

Please leave a review

Review Button
  • Product Code: PS 8048
  • Availability: In Stock
  • $14.99
  • 10 or more $12.00
  • 30 or more $10.00

Available Options

CSA Cement Fast Setting Additive 50 Lbs   GlobMarble CSA Cement is a cementitious po..

Paver stone molds  PS 15158/1 Plastic molds for concrete stoneApproximate Mold measurement: &n..

Rubber molds for concrete stone     PAVER STONE MOLDS   Application ar..

Plastic molds for concrete stone     PAVER STONE PLASTIC MOLDS   Appli..

Rubber molds for concrete stonePAVER STONE MOLDS  Application areas for paving stones incl..

Concrete Oxide PigmentOxide Concrete Colors for Concrete. 1Lb-(0.45kg) Mix Ready bag. Photos of..

Concrete Countertop Molds Edge Form CEF 7010Concrete Countertop Molds Edge Forms are used ..

Water-Based Concrete Stains-Eco-StainSemi-transparent Concrete Stains from SureCreteSemi-Transparent..

Color Pack for Decorative Concrete Overlay and Casting Products - 0.5 lb. (0.23 kg) Concrete co..

White Concrete PigmentTitanium Dioxide White Colors for Concrete.   SELECT COLO..

Concrete Countertop Mold Edge Form CEF 7012 Concrete Countertop Mold Edge Forms are ..