Concrete Stain - Concrete Acid Stain from SureCrete
Concrete Acid Stain from SureCrete - SureStain
Acid Stain Concrete (reactive acid) Stain comes in 8 earth-tone colors
SureStain - Concrete Acid Stain is not a typical concrete stain or dye. It is made from a very mild hydrochloric or phosphoric acid solution, wetting agents, and metallic ions (salts), and specially formulated pigments. When applied on concrete or any cementitious topping the metallic ions chemically react with the free alkaline in the cement forming oxides that produce the color. Unlike dyes that produce an even color, this Concrete Stain produces the multi-hued, variegated, mottled look of natural stone.
Earth Tones Colors perform similarly to other reactive concrete acid stains, but with very little residue at clean-up.
Concrete must be thoroughly cleaned before concrete staining. Liquid curing agents should not be used on concrete that is to be stained. Nothing should block the metallic ions from access to the free alkaline in the cement. For premier results in cleaning concrete prior to acid staining, use a black scrubbing pad with water on a rotational floor scrubbing machine.
Super Concrete Renovator (SCR) is recommended for every Concrete Acid Stain project on concrete. SCR is a mildly acidic detergent that cleans concrete thoroughly. Apply diluted at the ratio of 2:1 (2 parts water to 1 part SCR.) Coverage is approximately 150 sq. ft. per gallon. After spraying SCR from SP pump-up sprayer, agitate with a nylon bristle broom. Allow to stand until all foaming and bubbling has ceased. Do not allow SCR to dry on slab, rinse frequently. For interior slabs wet vacuum rinsed areas. For exterior slabs simply rinse away. The measure of profiling provided by SCR, permits the colors to go deeper into the concrete.
The Cleaner degreaser may be required for visible oil stains. Oil, grease, and other petroleum stains that are permanent will not accept acid stain. Concrete Acid Stain should not be used over petroleum stains.
SCR in a lighter dilution rate 4 or 5:1 (4 or 5 parts water to 1 part SCR) is recommended prior to concrete staining stamped overlay that has utilized liquid release for stamping tools. Interior stamp overlay projects where little, if any, evaporation of liquid release has occurred may require SureClean degreaser prior to staining.
Allow concrete to cure a minimum of fourteen (14) days. Cooler climates, (highs not reaching 50°F) require curing times of twenty-one (21) days or more. If applied to uncured concrete, SureStain will continue to change color until the concrete meets a complete cure. Therefore applying to cured concrete allows the contractor to identify final colors shortly after application.
Surrounding areas and foliage should be protected prior to staining. Any adjoining walls should be masked. The use of plastic sheeting for masking is appropriate, as it will not absorb and hold the concrete acid stain. Wear a NIOSH approved acid respirator and provide adequate ventilation. Wear chemical resistance gloves and chemical splash goggles. Wear suitable protective clothing to avoid skin contact.
Earth Tone Colors
Areas that may call for brushing are sloped surfaces, slabs with “bird baths,” stamped concrete, and overlays. Do not walk on the wet surface. Footprints will appear darker than the adjacent areas. If stepped on by accident, the footprints should be brushed out immediately. Allow the first coat to dry to the touch.
Apply second coat in the same manner as the first coat, as described above. Do not brush the second coat. Allow to dry overnight.
Colors may be layered or alternated as desired. For crisp, distinct, and separate color changes, a score line should be utilized. Concrete acid stain will bleed across traditional masking. Shielding or masking at a score line will prevent the bleeding of colors as long as the stain is not puddled heavily at score lines.
Unlike other reactive acid stains, this Concrete Stain leaves very little residue and requires no neutralization. For Earth Tones flood the surface with water. Very lightly brush. Either wet vacuum or mop. Allow to dry thoroughly.
For interior applications, the most durable sealers are any of the Dura-Kote line. For exterior applications requiring “breatheabilty” SureSeal Solvent is a suitable choice.
To apply with an airless sprayer, use a size 8/13 reversible tip and spray evenly onto the surface. Allow first coat to dry completely and apply the second coat in the same manner.
Decorative score lines that are to be grouted should be grouted between coats of sealer.
For interior applications SureFinish (see specification sheet) is recommended as an industrial floor finish that will act as a sacrificial coat to protect the sealer below and impart a measure of slip resistance. Provide slip resistance with SureGrip aluminum oxide or SureGrip Additive for exterior slabs.
Allow twenty-four (24) hours before permitting foot traffic on sealed area. Allow seventy-two (72) hours before permitting vehicle traffic on sealed area.